Vox VC-12 Spezifikationen PDF herunterladen (Seite 11)

11

English

Loading Program Data into Two Amps

Although you cannot store program data from

a Valvetronix amp connected to the VC-12’s

VOX BUS SUB connector, the same program

data is output by this connector during the

loading process, which means you can easily

load program data into two Valvetronix amps

simultaneously—one connected to the VC-

12’s VOX BUS MAIN connector, the other to

its VOX BUS SUB connector.

1. Turn off both Valvetronix amps and

make sure one is connected to the VC-

12’s VOX BUS MAIN connector, the

other, to its VOX BUS SUB connector.

2. On the Valvetronix amp connected to

the VOX BUS MAIN connector, while

holding down the DELAY [TAP] button

and the REVERB [TYPE] button, turn on

the amp.

The VC-12’s BANK shows

.

3. On the Valvetronix amp connected to

the VOX BUS SUB connector, while

holding down the DELAY [TAP] button

and the REVERB [TYPE] button, turn on

the amp.

The VC-12’s BANK display should still

show .

4. Press the VC-12’s BANK DOWN switch.

The VC-12’s BANK display shows .

5. Use switches 1 through 4 to select the

memory (1, 2, 3, or 4) containing the

program data that you want to load.

The switch’s LED flashes.

If you want to cancel the procedure at this

point, press the switch again, or press the

VC-12’s RECALL switch.

6. To load the selected memory’s program

data, press the VC-12’s CHANNEL–FX

ON/OFF switch.

The program data is sent to both

Valvetronix amps.

When the data loading process is com-

plete, “4.” appears on the BANK displays of

both Valvetronix amps.

7. Turn off both Valvetronix amps, and

then turn them back on again.

That completes the procedure for loading

data into two amps.

Deleting VC-12 Program Data

The program data stored in each VC-12

memory can be deleted as follows. This

procedure does not delete the program data

in your Valvetronix amp.

Warning: You cannot recover deleted pro-

gram data.

1. Turn off your Valvetronix amp and make

sure it’s connected to the VC-12’s VOX

BUS MAIN connector.

Note: Don’t connect anything to the VC-12’s

VOX BUS SUB connector.

2. On your Valvetronix amp, while holding

down the DELAY [TAP] button and the

REVERB [TYPE] button, turn on your

amp.

The VC-12’s BANK display shows .

3. Press the VC-12’s BANK UP switch.

The VC-12’s BANK display shows .

Switch LEDs (1–4) that contain no pro-

gram data are off, while those that do

contain program data are on.

4. Hold down the VC-12 switch (1, 2, 3, or

4) for the memory whose program data

you want to delete for at least five

seconds.

The switch’s LED flashes quickly.

If you want to cancel the procedure at this

point, press the switch again, or press the

VC-12’s RECALL switch.

5. To delete the selected memory’s pro-

gram data, press the VC-12’s CHANNEL-

FX ON/OFF switch.

The data is deleted and the corresponding

switch LED (1–4) goes off.

6. Turn off your Valvetronix amp, and then

turn it back on again.

That completes the procedure for deleting

program data.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 38 39

Kommentare zu diesen Handbüchern

Keine Kommentare